Wednesday, March 14, 2012

Re: [papercreters] Re: Earthbag, Superadobe, Hiperdobe, why not Hiperpapercrete?





This method certainly sounds like much more fun!, even for the technologically challenged. Have to ponder those bent corners for a while. From what you wrote before, I was thinking about using the drafts to let the pieces down slowly but they are much better at demolition than at careful and slow.
Clarissa




--- On Wed, 3/14/12, JayH <slurryguy@yahoo.com> wrote:

From: JayH <slurryguy@yahoo.com>
Subject: [papercreters] Re: Earthbag, Superadobe, Hiperdobe, why not Hiperpapercrete?
To: papercreters@yahoogroups.com
Date: Wednesday, March 14, 2012, 5:58 PM

 

There is another technique that is probably safer and used more often, but it has major drawbacks.

That is to simply unbolt all the lower bolts on a panel and leave one of the upper corners in place for last. Then make sure nobody is anywhere near where it will fall, and take off the last nut and go all caveman with a hammer to drive that last bolt out of the hole.

Wait for the big crashing sound to finish, and then go pick up the panel that just fell on a corner and bent it up.

If you don't mind bent corners, it works great. It's also a lot faster. Just make sure that the drop zone is clear of people every time you send a panel crashing to the ground.

This method is safe, fast, and fun. Bending the corners back strait... not as much fun. Trying to get panels to align correctly in a new installation location after bending them can be a major pain in the butt too. However if bent corners doesn't matter for the way you'll be using the panels, this might be the way to go.

--- In papercreters@yahoogroups.com, cloud wall <windwalkerwill@...> wrote:
>
>
>
> Am I glad that you decided to offer more help. I knew about the wind issues but never even thought about the weight and speed it would come down at. There's no such thing as lots of extra hands here so I have to think about this idea some more. It's good to know all of this before diving right in, Thanks, again.
> Clarissa
>
>
>
>
> --- On Wed, 3/14/12, JayH <slurryguy@...> wrote:
>
> From: JayH <slurryguy@...>
> Subject: [papercreters] Re: Earthbag, Superadobe, Hiperdobe, why not Hiperpapercrete?
> To: papercreters@yahoogroups.com
> Date: Wednesday, March 14, 2012, 2:46 PM
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>  
>
>
>
>
>
>
>
>
>
> Happy to help.
>
>
>
> Speaking of help.
>
>
>
> Have plenty of helpers on hand when you go to take one of those bins down. If you get a bin made out of the heaviest guage metal, those panels are not light, but even more importantly, they can be extremely awkward. More hands makes the work much easier.
>
>
>
> Don't neglect the incredibly obvious either. Choose a calm day with no wind, and WEAR GLOVES.
>
>
>
> The bolts may not break loose easily. If you have an air wrench and a portable compressor... it's a good time to make sure it's all oiled up. Of course, then you'll want ear plugs too. Those grain bins will resonate every pneumatic sound and make you deaf.
>
>
>
> The best technique I've seen is to have a few really long bolts. 4 inches long or so. Replace one of the bottom corner bolts for the panel to be removed with a long bolt and a nut, but leave it very loose. Then remove all the other bolts holding that panel up. Use that long bolt as a pivot point to swing the panel down. Those panels are not to be underestimated. They can be sharp and act like a gillotine. Take your time. If it seems unsafe, you're probably doing it wrong. Rethink your technique. Obviously nobody should be standing under a panel that is being removed.
>
>
>
> Using ropes to lower panels in a conrolled manner is smart, but don't let the ropes drag over sharp edges and get frayed or cut. Tape scraps of old carpet over the edges of panels still on the bin with packing tape or duct tape. The friction from the carpet will be your friend slowing the decent, but it will also protect the rope from damage.
>
>
>
> --- In papercreters@yahoogroups.com, cloud wall <windwalkerwill@> wrote:
>
> >
>
> >
>
> >
>
> > I've seen lots of those silos; usually missing their roof and begging to be recycled. This is a great idea!  I'm not at all attached to the gable roof. It just happened to be what I had to work with. I didn't realize those grain bins were a stronger metal, either. I could think of a few uses for that. Draft ~  proofing at the top of the list. Trying to withstand a 2200# butt scratching or kicking has been the biggest challenge. Thank you!
>
> > Clarissa
>
> >
>
> >
>
> >
>
> >
>
> > --- On Wed, 3/14/12, JayH <slurryguy@> wrote:
>
> >
>
> > From: JayH <slurryguy@>
>
> > Subject: [papercreters] Re: Earthbag, Superadobe, Hiperdobe, why not Hiperpapercrete?
>
> > To: papercreters@yahoogroups.com
>
> > Date: Wednesday, March 14, 2012, 1:03 PM
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >  
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> > You might keep your eyes open for old rusty metal grain bins.
>
> >
>
> >
>
> >
>
> > The cylindrical ones.
>
> >
>
> >
>
> >
>
> > If you can find a farmer that has an old one that is rusted enough that the bolts don't hold it together very well, those old grain bins become unusable. The grain pressure splits the seams and the grain falls out.
>
> >
>
> >
>
> >
>
> > Those old grain bins are made like a tank.
>
> >
>
> >
>
> >
>
> > The edges of the metal sections and the holes won't have galvanizing on them, so that is where the rust will form, and that is where the bins will fail. However, most of the metal is in great shape.
>
> >
>
> >
>
> >
>
> > If you were to consider a barrel vault roof, by using sections of an old grain bin, you might have a nearly indestructible roof for ... well maybe for free.
>
> >
>
> >
>
> >
>
> > You might be able to convince a farmer to give you an old rusted falling about grain bin, if you volunteer to take it down and haul it away.
>
> >
>
> >
>
> >
>
> > This is super heavy duty guage metal. Not the thin stuff typically used for roofing.
>
> >
>
> >
>
> >
>
> > In any case, if you see an old grain bin that's falling apart, take a close look and consider what you might be able to do with most of the metal.
>
> >
>
> >
>
> >
>
> > Something like this:
>
> >
>
> > http://s3.hubimg.com/u/1009014_f520.jpg
>
> >
>
> >
>
> >
>
> > The upper roof of the bins will rust faster than the walls. When the walls fail, it's at the seams. Think about using the wall panels as a roof, and cutting off the rusty seams or just painting them over with rust inhibitor. There are no rules that say a gable roof cannot have an arc to it.
>
> >
>
> >
>
> >
>
> > --- In papercreters@yahoogroups.com, cloud wall <windwalkerwill@> wrote:
>
> >
>
> > >
>
> >
>
> > > https://picasaweb.google.com/106060429030466659564/20112012BuildingTheShedrow?authkey=Gv1sRgCOPwvOKwz6DkEg 
>
> >
>
> > >
>
> >
>
> > > I almost forgot; for all my whining about that billboard roof, it has withstood 70mph winds without a hitch.
>
> >
>



__._,_.___


Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___